You must have a mother with the same sleeve and spiral ball groove diameter and thread. After cleaning with kerosene, apply lubricating grease to the ball groove, and then use a little oil needle. The ball on the needle and lubricating grease stand up one by one ball groove. After the mother of the inner sleeve is finished, use the screw to resist the rotating sleeve to press. The ball screw sleeve can be screwed in without squeezing the ball.

　　使用相應的類型的假軸安裝,但也相應的類型的鋼球,進口耐磨,如16螺桿直徑16假軸安裝3.175鋼球,32螺桿直徑32假軸安裝6.350鋼球,等等滾珠絲桿螺母安裝方法的詳細步驟:

　　Use the corresponding type of dummy shaft installation, but also the corresponding type of steel ball, imported wear-resistant, such as 16 screw diameter, 16 dummy shaft installation, 3.175 steel ball, 32 screw diameter, 32 dummy shaft installation, 6.350 steel ball, and other detailed steps of ball screw nut installation method:

　　1. 清潔滾珠絲桿螺母和滾珠軸承。

　　1. Clean the ball screw nut and ball bearing.

　　2. 把塑料珠塞(換向器)放回螺母內。安裝止珠器時，應注意止珠器的球形進出口與螺旋槽的光滑連接。

　　2. Put the plastic bead plug (commutator) back into the nut. When installing the ball stopper, pay attention to the smooth connection between the ball inlet and outlet of the ball stopper and the spiral groove.

　　3.油脂螺母。

　　3. Grease nut.

　　4. 把球放進螺旋槽里。注意，并不是所有的螺旋槽都被填滿，球是按照一個圓型園珠塞的原則放置的，我看到你的堅果似乎是4個圓型園珠塞，也就是4個圓型園珠塞。

　　4. Put the ball into the spiral groove. Note that not all the spiral grooves are filled. The ball is placed according to the principle of a round round ball stopper. I see that your nut seems to be four round ball stopper, that is, four round ball stopper.

　　5. 將螺帽旋進絲桿(注意不要使?jié)L珠軸承下落)。

　　5. Screw the nut into the screw rod (be careful not to drop the ball bearing).

　　6. 前后轉動螺母，檢查螺母運轉是否平穩。如果是，它的意思是好的。

　　6. Turn the nut back and forth to check whether the nut runs smoothly. If so, it means good.

　　滾珠絲杠螺母安裝滾珠其他方法

　　Other methods of ball screw nut installation，不建議自行拆卸和安裝螺母，特別是高導球絲杠。

　　First of all, it is not recommended to remove and install nuts by yourself, especially the high guide ball screw.

　　在發生意外損失的螺母或如果你已經刪除了螺母,重新安裝螺母如下:一個空心套筒外徑略小于直徑的螺絲底部水溝(約0.1毫米小),一個內徑略大于螺桿的外徑較大(0.5 ~ 2毫米),和一個長度超過螺母的長度(10 ~ 50毫米長)。

　　In case of accidental loss of the nut or if you have deleted the nut, reinstall the nut as follows: a hollow sleeve with the outer diameter slightly smaller than the diameter of the screw bottom ditch (about 0.1mm small), an inner diameter slightly larger than the outer diameter of the screw (0.5 ~ 2mm), and a length longer than the nut (10 ~ 50mm long).

　　空集裝在泡沫類軟對象結束時,穿入洗干凈沒有滾珠螺母,然后把干凈的每個圓槽成一個球,裝滿了一圈(gap以0.5 ~ 1.5球直徑大小為宜)輕輕旋轉空心套管,確認后順利,然后推動下的空心西裝一圈,直到完全填滿。

　　At the end of the foam soft object, the empty container is put into a ball without a ball nut, and then each clean round groove is made into a ball, which is filled with a circle (gap should be 0.5 ~ 1.5 ball diameter). Rotate the hollow sleeve gently, confirm it is smooth, and then push the hollow suit for a circle until it is completely filled.

　　拆卸的填料塞,插入空心套筒螺帽螺桿軸的結束,空心套筒用一只手,螺桿上的螺母螺釘另一方面,直到所有堅果順利螺釘進入有效螺紋槽螺釘?shù)囊徊糠帧８螅瑢⒂椭驖櫥妥⑷肼菽缸⒂涂祝⒙菽溉谐桃苿?dòng)2次以上，保證運轉平穩。更后，再次注入潤滑脂，完成操作。

　　Remove the packing plug, insert the hollow sleeve nut at the end of the screw shaft, and use one hand for the hollow sleeve, on the other hand for the nut screw on the screw, until all nuts smoothly enter a part of the effective threaded slot screw. Finally, grease or lubricating oil shall be injected into the nut filling hole, and the nut shall be moved for more than 2 times in full stroke to ensure smooth operation. Finally, inject grease again to complete the operation.

　　以上是導軌絲杠制造商為大家介紹的相關內容，想要了解更多內容，歡迎訪問網站：http://m.meihuajc.comThese are the related contents introduced by the guide screw manufacturer. For more information, please visit the website: http://www.jgongrun.com